Installation aliunid Gateway with Blinker Sensor + WirelessWire Gateway

Installation aliunid Gateway with Blinker Sensor + WirelessWire Gateway

Use this configuration if you want to read your electricity data through a Gateway with Blinker Sensor and you need to forward your WIFI signal with a WirelessWire Gateway.


Note: Installation 1/2 (Install Gateway with Blinker Sensor on electricity meter)
Your configuration consists of two devices. Put the WirelessWire Gateway aside for the beginning. You will be asked to install it later.


Product Overview: Gateway with Blinker Sensor




Go to your electricity meter and take the following with you:
- Your gateway with blinker sensor incl. accessories
- Your smartphone with the aliunid HOME app installed
- The name and password of your WLAN

Open the aliunid HOME app on your smartphone


Go to the menu (top left) and select the section "My electricity meters"


Click on "Add meter" and follow the step-by-step instructions


Select the configuration "Gateway with Blinker Sensor" + WirelessWire Gateway"


Scan the QR code from your Gateway with Blinker Sensor


Attach the supplied antenna to the body of your Gateway.


Now place your Gateway on top of your electricity meter or in a suitable place next to it (less than 30cm away).


Connect your Gateway to the power supply, if necessary with an extension cable.
It is important that you do not place the Gateway more than 30cm from your electricity meter, otherwise the sensor cable, which we will connect in a later step, will be too short.
As soon as the Gateway is supplied with power, the status LED in the body starts flashing.


Set Impulsrate
Select the Impulsrate of your electricity meter or type it in manually. This can be found on the housing of your electricity meter (unit imp/kWh).

If you cannot find your Impulsrtae, press the green bubble with question mark. Fred will then show you a list of the most common electricity meters and the corresponding pulse rate.



Choose WLW channel
Choose one of the available channels. Which one is only important if several parties in the same house want to install a Gateway.


Now place the centering aid exactly in the middle of the flashing light on your electricity meter.

If you can't find your flashing light, press the green bubble with the question mark. Fred will then show you a list of the most common electricity meters and the corresponding flashing light.


Now you can stick the round, adhesive dot in the middle of the centering aid.


Then attach the sensor head to the adhesive dot so that the aliunid flower faces outward.



Connect the sensor to the Gateway by plugging the cable from the sensor head into the body.


Finally, you can attach the Gateway next to your electric meter with the adhesive strips.
Pay attention to the following:
- the QR-Code on the body should still be accessible
- the cover of the electricity meter should still be removable


Firmware Installation
Now the required firmware is installed on the Gateway via smartphone.

A Bluetooth connection is required to tranfer the firmware from your smartphone to the Gateway. If you have not yet switches on Bluetooth on your smartphone, you will now be prompted to do so. (Attention: older Android models request your "Location access", which is an unfavourable designation, but we cannot change anything about this, as it is specified by Android).
If your smartphone has neither mobile internet nor WLAN reception, it will not be able to download the firmware. In this case, you should go to a place where you have reception and return to your electricity meter after downloading so that the firmware can be transferred to your gateway.


Your first Gateway should now be successfully connected (you can see this on the one hand when your smartphone switches to the next step, and on the other hand when the status LED in the housing lights up contantly).


Now proceed with the installation of the WirelessWire Gateway.

Installation 2/2 (Install WirelessWire Gateway)
This Gateway will establish a wireless connection between your WIFI and the main gateway at your electricity meter.


Product Overview WirelessWire Gateway:


Attach the supplied antenna to the body of your Gateway.

Go to a place with good WIFI reception and where you can place your WirelessWire Gateway.

Connect your Wireless Wire Gateway to the power supply, if necessary with an extension cable.
As soon as the Gateway is supplied with power, the status LED in the body starts flashing.


Now enter the information about your WLAN

The name as well as the password must be spelled exactly right (pay attention to upper/lower case, hyphens etc.

Your WirelessWire Gateway should now be successfully connected (you can see this on the one hand when your smartphone switches to the next screen, and on the other hand when the status LED in the housing lights up contantly).
After a few moments, you should see a new card with your just connected electricity meter under "My electricity meters".
The card shows the last measured electricity consumption value.

Click on the cogwheel symbol (bottom right within the card) to change the name or function of the electricity meter.

Return to the cockpit to observe your own power consumption measured in real-time.

    • Related Articles

    • Installation aliunid Gateway with Infrared Sensor + WirelessWire Gateway

      Use this configuration if you want to read your electricity data through a Gateway with Infrared Sensor and you need to forward your WIFI signal with a WirelessWire Gateway. Note: Installation 1/2 (Install Gateway with Infrared Sensor on electricity ...

    • Installation aliunid Gateway with Blinker Sensor

      Use this configuration if you want to read your electricity data through a Gateway with Blinker Sensor and WIFI is available on site. Product Overview: Gateway with Blinker Sensor 1. Go to your electricity meter and take the following with you: - ...

    • Installation aliunid Gateway with Infrared Sensor

      Use this configuration if you want to read your electricity data through a Gateway with Infrared Sensor and WIFI is available on site. Product Overview: Gateway with Infrared Sensor Go to your electricity meter and take the following with you: - Your ...

    • Installation aliunid Gateway with MBus

      Use this configuration if you want to read your electricity data through a Gateway with MBus and WIFI is available on site. Go to your electricity meter and take the following with you: - Your gateway incl. accessories - Your smartphone with the ...

    • Requirements for the installation

      To use your aliunid GATEWAY, the following requirements must be met: At least one of the following interfaces must be available on your premises: Electricity meter with pulse light emitting diode Electricity meter with IR interface (provided that the ...